Exactly How to Replace a Tub in Your Bathroom
Exactly How to Replace a Tub in Your Bathroom
Blog Article
What're your thoughts on A Step-by-Step Guide to Installing a Bathtub?
Mounting a tub isn't exactly brain surgery, yet it does need solid plumbing, woodworking, as well as in some cases, tiling skills. Changing an old tub with a new one is additionally a moderately difficult task. If the old tub is readily obtainable, the job can move easily; if you need to open a wall surface to eliminate the old tub and also position the brand-new tub, the task is a lot harder. In either situation, the project is within a house handyman's skills, although you will certainly need an assistant to leave the old tub and also set in the brand-new one. Ensure you have certified yourself for the work and fit attempting it. As opposed to employing a specialist to take over a halfway-completed task, it is better to take into consideration utilizing one prior to you begin. Opportunities are you may require an expert plumber to make tube links.
This short article will certainly help you mount a new bath tub in your bathroom if you have actually already gotten a new tub and also don't require to change the setup of your previous water supply pipelines.
Your devices as well as product checklist must consist of the following:
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your installment, then the first thing you must do is separate the supply of water. After doing so, activate the taps to drain any type of water continuing to be in the system. The process of eliminating the existing faucets can be quite troublesome as a result of the limited access that is typically the instance.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the taps. Have a fabric prepared for the continuing to be water that will come from the pipes. When the supply pipelines have actually been removed, use the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from transforming during this process. When the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleansed of any kind of old sealing compound.
Before carrying on to fit the brand-new faucets, contrast the pipe connections on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic connector to prevent damage to the thread. One end of the port fits on the plastic tail of the tap as well as the various other end supplies a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, place the faucet in the placing opening in the bath/basin making certain that the washing machines remain in area in between the faucet and also the sink. Safeguard the faucet in position with the maker supplied backnut. When the faucet is safely in place, the supply pipes can be connected to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular faucet adapters. The previous type ought to be connected to the tap finishes initially, tightening up only by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Setting up the Bathtub
Using both wood boards under its feet, position the tub in the required position. The wood boards are handy in equally spreading the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto four small factors.
The following goal is to guarantee that the bathtub is leveled all round. This can be attained by inspecting the level and also changing the feet on the bathtub till the level checks out level.
To mount faucets, fit the bottom of the furthest adaptable tap connector to the proper supply pipe by making a compression sign up with; after that do the same for the various other faucet.
Switch on the water supply and also inspect all joints and brand-new pipework for leaks and tighten them if needed. Fill up the bath tub and additionally inspect the overflow outlet and also the typical outlet for leakages.
Finally, deal with the bathroom paneling as described in the maker's instruction manual. Tiling and also sealing around the bathtub must wait until the bath tub has been made use of a minimum of once as this will certainly settle it right into its final placement.
Preparing for the Installment
First of all, the sustaining framework supplied with the bathroom ought to be fitted (if called for) according to the producer's instructions. Next, fit the faucets or mixer to the tub. When suitable the tap block, it is necessary to ensure that if the faucet comes with a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the faucets unit to avoid pressure on the bathtub.
Fit the versatile faucet ports to the bottom of both faucets using 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet with the hole in the bathroom. Utilize the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you use every one of the provided washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom must currently be ready to be fitted in its final setting.
Tiling Around the Tub
In the location where the bathroom fulfills the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is important as the fitting can move enough to break a stiff seal, triggering the water to permeate the wall surface between the bath and the tiling, resulting in issues with moisture and also feasible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to blend in your fixtures as well as fittings. They are offered in tubes as well as cartridges, as well as can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly load the bath tub with water prior to securing, to permit the activity experienced when the bathtub remains in usage. The sealer can fracture rather very early if you do not think about this activity prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are additionally conveniently readily available on the marketplace. It is a good idea to fit the ceramic tiles utilizing water-resistant or waterproof adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was brought to that article about A Step-by-Step Guide to Installing a Bathtub through a good friend on our other web page. Loved our review? Please share it. Help somebody else discover it. Thanks a lot for your time. Don't hesitate to come visit our site back soon.
Book Now! Report this page